You love flowers, but you can’t keep them fresh for more than a few days. What should you do? Epoxy resin will help to preserve your beautiful roses or tulips so that they stay healthy and vibrant for months! To learn how to use epoxy resin on flowers, read this blog post!
Can You Put Fresh Flowers In Epoxy Resin
Yes, you can! Epoxy resin will both preserve the freshness of your flowers and make them water resistant.
They’ll last for a while before they begin to fade, which is much longer than if you’d submerged them in water or other liquids.
The epoxy coating also makes it harder for dust particles to settle on top of the surface, so that applies for double protection against any kind of dirt or filth getting onto your flower petals.
You should be aware though that this process does not allow proper breathing room for the plants because there are no holes drilled into it to let air come through from underneath.
That means that if after some time you remove these pieces out of epoxy resin (or even just pick up one piece), you will see that the flowers are completely dried up.
Table of Contents
- Can You Put Fresh Flowers In Epoxy Resin
- How Do You Use Epoxy Resin To Preserve Flowers
- Do You Have To Dry Flowers Before Putting Them In Resin
- How Do You Preserve Fresh Roses In Resin
- How Do You Keep Things From Floating In Resin
- How Do You Dry Flowers And Keep Color
- How Do You Preserve Fresh Flowers Permanently
- How Do You Preserve Flowers With Glycerin
- How Do You Dry Flowers For Resin Casting
- How Do You Dry Flowers With Resin
- How Do You Seal Dried Resin Flowers
- How To Dry Flowers For Resin With Salt
How Do You Use Epoxy Resin To Preserve Flowers
First, remove the stems from your flowers. Be sure to avoid sharp objects like scissors or knives as you’ll be pushing them down into the epoxy resin which can cause it to crack and leave little lines in your project.
Remove any leaves that are attached to the stem by snipping a few times along each side of where they attach until everything is removed.
Then dip both ends of your flower heads into a container full of water for around ten seconds before placing them on paper towels.
this will help clean off excess dirt that might have been left behind during removal.
Do You Have To Dry Flowers Before Putting Them In Resin
No, you don’t have to dry flowers before putting them in resin. In fact, epoxy can be used on fresh flowers! However, dried and pressed flowers work great with this technique too.
If your flower is very small or it has a tiny hole at the bottom where water will collect during curing, because of its weight then you need to let it dry first otherwise when the epoxy dries, it may break off from the stem making your beautiful preserved flower wilt away which would be such a horrible thing!
But if that doesn’t apply to your type of flower you can just skip drying altogether and add some preservative medium like Mod Podge so they last longer without drying out while waiting for epoxy to cure.
How Do You Preserve Fresh Roses In Resin
There are so many different ways to preserve flowers with epoxy resin. It’s also very easy!
Just follow these steps:
Step One:
Find a container to place your flowers in. You can use plastic, glass, or even metal containers.
Make sure the container you choose is big enough for your flower but small enough so that it fits inside of it nicely without too much space around them.
This also means that if you are using something like glass then you don’t need to worry about scratching up anything with sandpaper since there won’t be any exposed edges on the final product!
Step Two:
Grab some kind of adhesive material (ie yarn) and start tying together each part of your flower where they would normally connect i.e. the stem and leaves.
As you can see in this example I have tied my flower together with yarn so that when I place it into the epoxy resin there is no chance of separation or damage to any part of the petals.
Step Three:
Place your flowers inside your container making sure they are nice a snug without too much space around them, as mentioned earlier!
If you notice that some parts look like they could move freely then do not be afraid to tie those down also!
This will ensure that every piece stays where it belongs during curing time which ultimately makes for a better end product!
Once everything looks perfect go ahead and mix up your two components according to directions on bottle (usually equal parts) and pour them into your container.
Let it sit for a few days and you will have yourself some beautiful flowers preserved in resin!
How Do You Keep Things From Floating In Resin
a small number of metal washers or nuts in the bottom of your container will allow it to float just enough for you to add items underneath.
This is a good idea when making multiple layers!
How Do You Dry Flowers And Keep Color
Many people like to dry flowers for their preservation and use in floral arrangements. You can buy wires that have round or square shapes which allow you to insert stems into them before placing the flower on a paper towel to dry.
Simply fold the paper towel over beside the flower, beside the stem, then twist both ends of thread around each other between your fingers until they are pulled tight. This will work well with roses, daisies, carnations, or any other type of stem flower.
How Do You Preserve Fresh Flowers Permanently
You can also add a little bit of lavender oil if you want the flowers to have a nice fragrance during the process.
Preserving fresh flowers is possible by using resin, although it will never look as clean and crisply-cut as real flowers on top of an arrangement.
Epoxy resins are clear and completely dry when fully cured (usually in 24 hours). They’re not toxic like some other chemicals that preservationists use, and it comes in liquid form that artificially colors the resin to match your colors.
You won’t be able to reuse this product but most epoxies dry into such a hard coating, they don’t need reinforcement for durability.
Follow these simple steps:
- mix equal parts of each resin and hardener.
- apply to flower with a paintbrush or plastic syringe (if you’re planning on using it for larger batches).
- place in the sun until dry, which should be within 24 hours depending on humidity levels. You can also put them inside an oven set at 150 degrees Fahrenheit if direct sunlight is not available. All epoxy resins will fully cure as long as they are exposed to air; otherwise, your flowers could remain tacky after curing!
How Do You Preserve Flowers With Glycerin
You’ll need to dissolve one part of the glycerin in two parts water. The ratio is important because it allows for the right consistency and density needed to maintain your flower petals’ moisture levels.
This means not too thick or too thin! Once this mixture has been prepared, you can take your flowers and soak them in them for a few minutes.
Afterward, remove the petals from the glycerin mixture and lay them on paper towels to dry.
How Do You Dry Flowers For Resin Casting
You can dry flowers for resin casting by placing them in a paper bag and leaving it on the radiator, or with silica gel.
How Do You Dry Flowers With Resin
What you need: flowers, an epoxy resin kit, and a brush.
How Do You Seal Dried Resin Flowers
These Dried flowers come in different shapes and sizes, so the first step to preserving them with epoxy resin is selecting appropriate flower molds or cups for your dried blooms.
You should select a flower cup that will fit nicely into your design so you can focus on creating dimensional pieces.
How To Dry Flowers For Resin With Salt
If you are looking for a fast method, this might be it. Place your fresh flower petals on top of the Epsom salt and place them in direct sunlight A day or two later they should have dried out enough that you can pour epoxy resin over them without issues.
