can you epoxy painted concrete?

Concrete floors can be painted with epoxy, but there are some things to consider before you decide on this method of resurfacing.

This article will explore how to paint a concrete floor that is already painted and what types of paints can be used to cover the old coat. We’ll also look at why it’s important to remove old paint before painting over it with epoxy.

Can epoxy be applied over paint?

Yes, you can apply epoxy over paint. However, the paint must be removed first. This can be done by either sanding down the existing layer of paint or stripping it.

You’ll want to make sure that you remove all of the dust from your surface before applying epoxy because particles in your epoxy will create air bubbles and cause it to crack.

It’s also important that you use a clean surface when applying epoxy over paint so that there are no contaminants on the concrete that could ruin your project later on down the line.

Even though it may seem like there are many steps involved in applying epoxy over painted concrete floors, it won’t take long before they’re looking brand new again!

Can you resurface painted concrete?

You can resurface painted concrete. It’s a simple task that requires only a few materials and a bit of elbow grease.

To resurface your painted concrete, first use an old toothbrush or scraper to remove any loose paint from the surface.

Then, use a pressure washer to wash down the rest of the surface before applying epoxy bonding primer.

After letting it dry for about an hour (or according to instructions), apply two coats of epoxy bonding primer using either roller or brush application methods.

You’ll need about two gallons per coat for larger areas like driveways and patios; one gallon per coat for smaller areas like sidewalks and porches.

Let each coat dry thoroughly before applying another one. Once all coats have dried, sweep up any dust with a broom or vacuum cleaner then let it sit overnight before walking on it again.

Can you paint concrete before epoxy?

Before you can paint concrete, you’ll need to remove the previous coat of paint. Most paints are oil-based and should be removed using a solvent like mineral spirits or turpentine.

You may need to scrape off the old paint down to bare concrete as well.

Once the old paint is gone, you can prime and then apply your epoxy coating as usual.

How do you paint a concrete floor with epoxy?

If you’re looking to paint your concrete surface, follow these steps:

Prepare the surface.

If the concrete is new or has been recently resurfaced (within a year), it should be fine to skip this step; however, if it’s older than that and has developed cracks or texture, you’ll need to smooth out those imperfections before attempting to apply epoxy.

Epoxy needs a smooth surface on which to adhere. If there are large cracks in your floor, fill them with lime putty or thin-set mortar using a trowel, and then sand down any rough edges with 80-grit sandpaper so they’re smooth enough for epoxy application.

If the floor is textured or porous due to previous repairs and patching work done by hand troweling or power troweling without proper equipment (which can create small pits), clean out all of these irregularities using an angle grinder fitted with an 80-grit metal cutting disc followed by 120-grit paper).

This will ensure that your epoxy coats evenly across all areas of the floor as opposed to leaving some areas bare while others get coated twice over from overcoating!

How do you paint a concrete floor that is already painted?

While it is possible to apply epoxy over previously painted concrete floors, it may not be the best option. As with any painting project, you will need to remove the old paint and then clean and sand down the surface before applying new paint.

In order for epoxy to adhere properly, you must also remove any existing sealer on your floor.

Epoxy products are made specifically for use on concrete surfaces and are generally considered a more aesthetic alternative to a polyurethane coating.

They come in two types: wet-look (gloss) or matte finish (satin). Both types are typically applied using one of two methods: roll-on coatings or spray application; however, some manufacturers recommend that roll-on coatings be applied by brush rather than roller so as not to trap air bubbles under the film layer. The thickness of these films is about 1/4 inch (6 mm).

Do you need to remove paint from concrete before repainting?

  • Yes, you should remove paint from concrete before repainting.
  • If you use a pressure washer, the paint will be removed in sheets. If you use a scraper or sandblasting, the paint will chip off in chunks.
  • You can also use chemical strippers to strip away old layers of paint and floor finishes (if any).

How do you resurface concrete that has been painted?

You can resurface painted concrete with an epoxy sealer. Epoxy sealers are durable and can be used on many different surfaces, including painted concrete.

First, remove the paint from your surface by using a pressure washer and a long-handled steel brush to scrape away any loose paint.

The next step is to clean your surface with a pressure washer again to remove any dust or dirt that might have accumulated after removing the old paint.

The last step is applying an epoxy coating to your surface by spreading it evenly over the area you want to be covered.

Make sure you use plenty of overlapping strokes when applying this coating so that it is nice and smooth when dry (about 24 hours later).

What can you put over painted concrete?

  • Epoxy
  • Polyurethane
  • Latex paint (not as durable)

In addition to these options, you can use a concrete sealer. This is a good choice if you want to preserve the natural look of your concrete floor and don’t have time or energy for any sort of painting project.


The answer to the question “Can I paint concrete?” is yes. You can paint your concrete floors, walls, or even ceilings with any type of paint that suits your needs.

It is important to know exactly what kind of paint will work best on your surface before starting this project though as there are many different types available!

Photo of author

Martin Flood

Martin Flood has been working in the construction industry for over 20 years as a general contractor with expertise in remodeling projects that are large or small. He has furthered his career by specializing in epoxy resin flooring, providing excellent service to both commercial and residential clients. Martin’s experience enables him to offer professional advice on how to choose the right type of project based on your needs and budget.

Leave a Comment